To start off this long winded explanation of a problem I will say I have a 2018 Samsung QN55Q6FNA QLED TV that performed all functions as expected until I upgraded my router/modem.
I was previously using Optimum's Modem Arris TM1602 and Optimum's Router Sagemcom F@st 5260CV and all services were working fine on my TV. I upgraded to the brand new Netgear Nighthawk CAX80 and when I connected my TV to the network, TV Plus stopped working. All channels appear in the channel guide and are selectable but when I select a channel it does not load and instead provides an error message "Error. There was a problem while trying to play the TV PLUS channel. Check your network settings or try again later." I must specify ALL other internet connected apps have been working as usual (Netflix, Hulu, Amazon Video, etc.), only TV Plus is encountering this issue.
In terms of troubleshooting, I've tried everything I could think of including: Upgrading Firmware (current T-KTM2AKUC-1294.1, BT-S), resetting network connection, using wired connection, using wireless connection (only 2 feet away from router), auto scanning channels again, turning off IPv6, power cycling TV, unplugging/plugging back in TV, signing in/out of Samsung Account, Resetting Smart Hub and ultimately doing a factory reset. However, I did try connecting the TV to my phone, using my phone as a hotspot and boom! TV Plus started working again. Then, I connect it back to the router and TV Plus goes offline again.
These steps led me to believe for sure it is a router issue somehow blocking access to TV Plus. That is until I remembered I have a 2016 Samsung UN43KU6300 that I rarely use for streaming purposes. I figured let me give TV Plus a shot on the older TV. Using the same wireless connection, to my surprise, TV Plus started working on my 2016 TV, running on software version 1242. A quick note about that 2016 TV is that it had been acting up ever since my house was struck by lightning (2018) while it was powered on, frying the main board. I had managed to obtain a new main board, pop the covers off and replace the fried board to successfully revive the TV but still things sometimes act up a bit. Besides the point, my thought now is that the newer software version 1294 is somehow not compatible with my router in terms of TV Plus but the older version is. Is there a way I can downgrade my 2018 TV's version to match the 2016 TV, flash drive side loading perhaps?
It is also worth noting my old modem Arris TM1602 was using the DOCSIS3.0 protocol while the new router/modem combo uses the DOCSIS3.1 protocol.
I have been in contact with Samsung Experts who have taken remote control of the TV and after 50+ minutes came up with the conclusion that it must be the Modem/Router causing the issue (since it worked on my mobile hotspot) and redirected me to my Modem/Router Supplier. I then contacted Netgear Experts to tell them everything I had learned only for them to tell me it must be a TV issue (since the 2016 TV connected) and they redirected me back to Samsung. I fear I will be in this Ping Pong of deflections for eternity which is why I came to this message board.
If anyone has any knowledge or information please share. I am an engineer and a perfectionist and it's eating away at me not knowing the solution to this problem! Thank you all who have read this far!
Solved! Go to Solution.
I'm sorry to hear about that. as of lately it unfortunately started happening again..I just gave up since nether samsung and net gear dont know why, but even the q80t samsung tv plus does not connect wit the router as well, but my 2016 8000 series work perfect with the router. its gotta be on how the data communicate with each other. its like it being block but I just said <HIDDEN> ill give them 4 years and they will bound to find the problem
So the best way to troubleshoot this type of issue would be to do a packet capture. Based on my quick research, it appears that the CAX80 is capable of doing this. If you go to the Web UI of your router (usually something like http://192.168.1.1) and add /debug.htm to the end, you should see an option to enable the packet capturing. Please enable that feature and reproduce the issue (try and do this quickly and, ideally, without other devices active as to limit the size of the packet capture) then stop the capture, download the .pcap file, zip it up, and send it over via private message. I will take a look and see if I notice anything odd.
Another thing you could try would be to put the TV in the DMZ of the CAX80. See page 40 of this guide.
Alternatively, while not what you want to hear after shelling out hundreds of dollars on the Nighthawk CAX80, I would strongly suggest buying a modem separate from a router. While it may be tempting to get an all-in-one, it's one of those situations where it may do multiple things but it doesn't do either very well. You are also at the mercy of the ISP to push firmware updates that are compatible with their network. With the two separate devices, there are several benefits. You have purpose-built equipment that does one thing and does it rather well. Plus, if one of the functions fail, you aren't throwing out the entire system, you are just replacing that one piece. I personally have a separate modem (Surfboard 8200) and router, which works very well.
Information Technology Management Professional (15+ years)
QN75Q80TAF QLED TV & Q900T Soundbar
An Accepted Solution has been marked and provided for this thread. The thread will now be locked for further replies. in hopes to keep the integrity of the thread from steering in a non-technical manner. If you have a separate concern, feel free to post again or send one of our moderators a private message with more details. Please note duplicate posts on similar subjects starting 2/1/21, will be removed to keep our community organized and make it easier for our users to find resolutions and needed content. Remember that if you do make a post, please include as many details about your symptoms as possible. Also, make sure that your title is a good summary of the overall situation that's occurring with your product. Thank you for being part of the community!
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.