- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-18-2020 09:29 PM in
Washers and DryersDryer shuts off after a couple minutes and shows a HE code. I cleaned all the vents, & replaced the Heat Exchanger, Thermostat. It didn't fix the problem and I have no idea now what it could be?
Any suggestions would be helpful.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
07-19-2020 07:52 AM in
Washers and DryersCan you provide me with your full model code?
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-21-2020 03:56 PM in
Washers and Dryers- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
07-21-2020 04:56 PM (Last edited 06-24-2022 09:38 AM by SamsungAl ) in
Washers and DryersThis error code (HE) means that the dryer is getting too hot.
The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error. If the error code hasn't gone away, the dryer will require service. Could you send me a private message with transaction numbers from your previous repairs or your dryer's model code and serial number? http://bit.ly/2ihPL97
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-22-2020 12:14 PM in
Washers and DryersPlease provide the serial number as well. When was the dryer purchased?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-06-2021 03:46 PM (Last edited 05-22-2022 09:26 AM by SamsungJecca ) in
Washers and DryersI'm the homeowner. About 6 weeks ago the dryer stopped - drum would not turn, error showed tO. Ordered OEM heating element assembly and thermistor. Replaced heating element assembly, no change. Replaced thermistor. Dryer began working fine. Now, 6 weeks later, the dryer will run for less than a minute, stops, and it shows an hE (overheating) error. No lint issue. Pulled new heating element assembly out. Tested for short on new heating element. No issue. Put original assembly back in after testing for short on old heating element. No short on old element. Started dryer and same behavior, runs less than a minute, stops, error code hE. Would appreciate next suggested troubleshooting steps. Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-06-2021 03:59 PM in
Washers and Dryers- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-06-2021 04:01 PM in
Washers and Dryers- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-06-2021 04:03 PM in
Washers and DryersI will be happy to assist you. You will want to check the vent to make sure the damper is opening, and there are no other blockages. An easy test is to disconnect the vent from the back to see if the dryer runs normally. You can find other troubleshooting information at the following link. https://www.samsung.com/us/support/troubleshooting/TSG01207445/
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-10-2021 04:10 PM in
Washers and DryersI guess that I should not have been so concise. No lint issue meant that I had checked everything for kinks, blockages, lint build up, in other words, no airflow problems. That was the first and most common step in everything I read online before posting.
My wife ran the dryer on the air-fluff setting (no heat) and the dryer ran for a long time with no issues.
Are there any tests I can perform to confirm that as 'springdinger' suggested, the main control board is at fault?
And by the way, SamsungLou , Mr. Moderator, the link you posted just takes you to the error code page that essentially says: Check for lint/blockages/airflow issues, and if not call for service. Not very helpful.