I've been fighting an issue for a few weeks now. wf45h6300aw/a2
Our Washer won't start 90% of the time. My wife will load the clothes and then hit the Start button and recieve a beep back. Turning it on and off several times will sometimes get it to kick in and start going. Hitting the power button only changes the display to OFF, but it never turns off.
Being the IT guy/DIY guy that I am, I decided to try and research the issue and fix it. So far here's what I've done.
1. Removed the front panel and looked for moisture buildup. I didn't want to pry up the touch button's circuit board to check under there for moisture. Re-assembled the front panel and still gettign the same results.
2. Tried to use the diagnostics mode to see what it reported. Held the 2 childlock buttons and then hit power. All lights on and it seemed to be in Diag mode. However, turning the Dial does nothing. Hitting the Start/Pause button does nothing. Hitting power again just says OFF and doesn't actually turn off.
Anyone have any ideas? I'm hoping this is under some extended warranty, but it seems like it's a PCB that needs to be repalced and not the drivetrain. It's just over 3 years old.
Solved! Go to Solution.
If your washer won't start, the buttons won't work, will not turn on, or the control knob won't select a different cycle, you probably have Child Lock turned on. If your Child Lock icon is lit or flashing, this confirms it. Turning Child Lock off will usually take care of your problem. If the Child Lock is off and the unit still won't start, continue with the steps below.
Moisture in the panel is normal, especially if the washer is in a humid location. Allow the panel to dry and try again.
Some settings and features do not work with every cycle. If the button works on some cycles but not others, this is normal. See the appendix in your user manual for which settings can be used with each cycle on your model.
The outlet needs to be a well-grounded, 120V, three-prong outlet, protected by a 20-amp circuit. To confirm the outlet is working, plug in something else, like a lamp.
If the power cord is damaged, visit our Support Center to request service.
Your washer and dryer will typically share the same circuit, although electric dryers require a 240V outlet that a washer cannot use. Do not have any other devices on the same circuit as the washer and dryer.
Tripped circuits often look like they're on (see the lowest circuit in the image). To be sure, switch the circuit off, then back on again.
Samsung does not recommend using surge protectors with our washers.
Note: Make sure that you are quickly pressing the button down instead of holding it down
If the above troubleshooting steps didn't help, here are some service options:
- If your unit was recently purchased, you can check with your retailer on their return/exchange process.
- If you have an extended warranty you can reach out to them to have service processed.
- If you're within the one year warranty, you can Private message one of our moderators to have service set up. https://bit.ly/2tWAAvS
- If you're OUT of warranty, you the following link to locate a service center in your area by using the link below
Instead having every single "SOLUTION" in this thread across google searches is all of you saying "Send us a message"--how about you post an actual SOLUTION or something every person looking in forums can at least try?!
My dryer control pad stopped responding nearly a year ago. At first it was intermittent but escalated quickly. I can no longer change out of active wear. I can't change heat level or anything. It does power up and the start/pause button works. The display lights up as normal and will show the amount of time remaining. It just does not respond to my finger. It sometimes also runs much longer than necessary; it will show that there is still over an hour remaining long after the load is dry. Just recently, I had a load that just wouldnt dry. I had to keep turning it on. That did, however, seem to be an isolated load. The model number is DV457GVGSWR/AA 02. Serial number is <HIDDEN>.
The washer just started doing this. I just put another load in the washer and it was even more difficult to start, it would just do a single beep and nothing, no error code or anything. Again, the washer model number is WF457ARGSWR/A2 and serial number <HIDDEN>.
Your assistance is very much appreciated!