Loud humming, buzzing, or grinding noises imply that something is caught in the drain pump's impeller below the filter.
Inspect the drain filter and pump (applicable models only).
If your model allows for it, inspect and clean out the filter and drain pump opening under the filter.
If your filter and drain pump opening are not accessible, but the grinding/buzzing is loud and happens every cycle, this will require service.
Check the water supply.
Make sure it is connected to the dishwasher.
Make sure the home's water supply is turned on.
Verify it meets all requirements listed in the guide for water supply requirements.
Make sure the dishwasher cabinet insulation (the fabric on the outside of the dishwasher) is in good condition. It is there to dampen sound and hold in heat.
If this does not help then service will be required, depending on the warranty of the unit you do have a couple of options.
If the unit is in warranty you can send me or any of the other moderators a private message with your full model and serial number and we can get that set up for you.
Or if your unit is out of warranty you can use the link below to find a service center in your area.
http://www.samsung.com/us/support/service/location
... View more
Starting on page 131 of the user manual you can see all supported resolutions.
https://downloadcenter.samsung.com/content/UM/202004/20200403095308351/NIKATSCT-3.0.1_EM_NIKE_USA_ENG_200323.0.pdf
... View more
Repairs would be recommended for this please send me a private message with your full model and serial number so that I may look into this?
... View more
I would recommend reaching out to our Smart Things department regarding your concerns. They can be reached directly at 866-813-2404 or you have an option to email them at support@smartthings.com.
... View more
The model should be on the bottom sticker of the soundbar, also you should be able to the firmware version using the smart things app or the multiroom app.
... View more
Just to confirm have you tried calibrating your washer? You can do that by doing the following:
-Calibrate your washer.
Your washer senses the weight of your load to determine how much water to deliver. Recalibrating the weight detection ensures that the right amount of water is being used.
The two buttons to press for Calibration Mode varies between models, and you can see your user manual for the steps specific to your model. Here is the most common method:
Note: On some models, you do step 2 while the washer is already on. On other models, you start with the washer off, hold the two buttons, and then touch Power to turn on the washer while holding the buttons.
Remove everything from your washer.
Simultaneously press and hold Temp. and Delay End for 3 seconds until Cb appears on the display.
Press Start/Pause. The tub will rotate back and forth for 1-3 minutes, then display En, End, or 0, then turn off. The washer is now calibrated.
... View more
I'm sorry to hear that, have you tried a factory reset on the TV? Also have you made sure that your TV is up to date with the latest software available to the TV?
... View more
Everything is up to date with your TV the next step would be service can you please send me a private message with your full model and serial number so that I may look into this?
... View more
On page 7 of the user manual should be able to help you the most, it will need a Vesa mount with a 400x300 screw wholes and the spacers go in between the mount and the TV. Samsung also recommends a professional install to install the TV.
http://downloadcenter.samsung.com/content/EM/201902/20190208122345757/BN68-09450A-00_Q70R_ZA_ENG_US_190115.1.pdf
... View more
I'm sorry to hear that, since changing the cable did not help it could be the one connect box itself, if you are out of warranty you can use the link below to be able to purchase a new one or if your TV is still in warranty you can send me a private message with your full model and serial number.
samsungparts.com
... View more
I'm sorry to hear that, could I have your current software version? Also how long has this been occurring? I see that you are trying to factory reset the TV are you able to sue the buttons on the TV to select the factory reset?
... View more
‎03-15-202012:08 PM (Last edited ‎10-13-202303:18 PM by SamsungAl) in
‎03-15-202012:08 PM
Remove the water filter and put it in again.
The water filter will always reduce water pressure slightly, but when it reduces water pressure by a significant amount, that means it's time for a new water filter.
Caution: Use only Samsung brand water filters.
If the water line is kinked, unkink it and check for holes or damage to the line. As long as the line is not damaged, further kinking in the same place can be prevented by wrapping duct tape around the kinked area. If the line is damaged, it will need to be replaced.
Increase the water pressure.
Open the home's water supply valve more fully in order to increase water pressure. If the home's water supply valve is already open all the way, the home's water pressure is too low.
The refrigerator requires water pressure of at least 30 psi. Most city water is around 60 psi, however, filtering systems such as reverse osmosis can significantly reduce water pressure.
If the home has low water pressure, a booster pump may be needed to get the water pressure to the appropriate level. For further assistance, contact a plumber.
If the above troubleshooting steps didn't help, here are some service options:
- If your unit was recently purchased, you can check with your retailer on their return/exchange process.
- If you have an extended warranty you can reach out to them to have service set up.
- If you're within the one year warranty, you can private message one of our moderators with your full model and serial number to have service set up. http://bit.ly/2XERsky
- If the unit is out of warranty, you can use the following link below to request service or contact our phone support line at 1-800-Samsung to have service set up for you:
https://www.samsung.com/us/support/service/
... View more
‎03-08-202002:08 PM (Last edited ‎12-13-202211:46 AM) in
‎03-08-202002:08 PM
Hello! Thank you for reaching out! I can see how this can be an issue with your screen having a line across the bottom. If this is occuring on all sources then this will require service. Depending on your warranty you will have a couple of options.
- If your unit was recently purchased, you can check with your retailer on their return/exchange processes. - If you have an extended warranty you can reach out to them to have service set up. - If you're within the one year warranty, you can Private message me or one of our moderators or you can call in directly at 1-800- 726-7864 with your full model and serial number to have service setup - If you're OUT of warranty, you can use this link below to find a service center in your area.
https://www.samsung.com/us/support/service/locations/
Opens in new window
PDF Download
Word Download
Excel Download
PowerPoint Download
Document Download
... View more
