- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-25-2019 01:49 AM in
Home TheaterI have the MX-JS9500 and it will not communicate via bluetooth, it just says wait. I have attempted to update the formware and usb just sits there with Read flashing on the display. There is no sound if I select tuner and the cd will not open, display just reads open... Is there a procedure to do a hard reset on the unit? Is the unit in safe mode or something?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
06-25-2019 09:51 AM in
Home TheaterTo reset your device, press and hold the stop button (on the front panel) for more than 5 seconds.
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-25-2019 05:38 PM in
Home TheaterI tried that already and it did nothing
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
06-25-2019 05:59 PM in
Home TheaterThis device may require a service technician to take a look at the device. What type of device are you trying to connect to the Sound System?
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-26-2019 04:10 AM in
Home TheaterIt doesn't matter what I am trying to connect, bluetooth used to wake her up just by connecting, now it won't even show. With BT selected it just flashes Wait. If I press the cd open/close button it just displays open and will not open the tray. Tuner will display stations and move through the range but no sound. Volume moves through the scale when thje knob is rotated but again, no sound. No sound from party beat. USB slot illuminate when selected but if there is a usb device in the slot, only flashes Read.All lights work. It's like the main processor has took a dump or something else. I did notice that when I would turn it on in the past that I could hear the fan, of which now it does not seem to be running, but there is no message of any failure or safety.
It could be a simple matter of the fan rotation not being detected and the system won't go any further, if the fan has a feedback to tell the main board it is operational. I haven't opened the case yet to check it. The unit is defenitely out of warrantee so that won't void anything.
i may have to see what it will cost to send in for repair....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-26-2019 10:07 AM in
Home TheaterWe can set up a ticket so you can get a repair estimate. Please send the following information to this PM Link:
Serial Number:
Place of purchase:
First and Last Name:
Physical Street Address:
City, State, and Zip Code:
Home phone number:
Alternate phone number:
Email address:
Preferred method to be reached by service center (SMS, email, or phone):
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-26-2019 06:19 PM in
Home TheaterHere's where I am. Unplugged the power this morning and left it unplugged all day, got home from work and plugged it in and she is working now! Yaay!
Still wierd though as I went ahead and tried the firmware update and it says it updated but following the instructions vfor the firmware, after it updates and reboots, I held the Play button in for like ten seconds to "Initialize", it never did say that. I tried holding the stop button in for same amount of time and still no Init. Am I missing something? Everything still seems to work again now though.
Does the system really need initialized after the update and if so, how do I do it?
Thanks everyone for your help, by the way!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
06-27-2019 09:18 AM in
Home TheaterOkay, great! I am happy to hear that your unit is now working. If the unit is working now it does not need to initialized. Please let us know if you need assistance in the future!
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-27-2019 06:20 PM in
Home TheaterI will! Thank you and everyone for the help.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-24-2019 01:28 AM in
Home TheaterWell, bad news it went back to not responding. So I am going to have to send it in for repair...