- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎06-09-2021 11:49 AM in
QLED and The Frame TVsI have a QLed TV that we bought back in September 2020. For the past 3 months, every time I turn on the TV and try to open any of the apps, a window pops up saying "Error: Unable to connect to the network". However, if I go in the network settings and try to reconnect the TV to the WiFi, it fails to even connect to any of my two routers. I've tried forgetting the network and reconnecting to it, but it also keeps failing. The only way I can have internet is if I reboot the TV by holding the power button.
In short, for the TV to be connected to the internet, I have to reboot it EVERY TIME I turn it on. Besides that, it works just fine and has a stable connection to the routers.
My question is: how do I stop this from happening?
Solved! Go to Solution.
1 Solution
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
‎06-10-2021 05:21 AM in
QLED and The Frame TVs I recommend letting a service technician have a look. As we would like to gather additional information and look at this from a case by case basis please provide the full model code and the serial number of the device as well as your best contact phone number, name, and email.
Send a message on Facebook
Send Message on Twitter
Send Message to Moderator
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
‎06-09-2021 03:01 PM in
QLED and The Frame TVsI do apologize for the inconvenience this has caused. when holding the power button down does the unit show the tv logo upon turn on?
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎06-09-2021 03:11 PM in
QLED and The Frame TVsAfter about 5 seconds of holding the power button, it shows "QLed" on the screen, and then it goes to the home page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
‎06-09-2021 04:33 PM in
QLED and The Frame TVsCan I have your full model number and current software version number?
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎06-09-2021 11:03 PM in
QLED and The Frame TVsThe full model code is QN50Q60TAFXZA
The current software version is 1460 (in the "About TV" section, it says "T-NKLAKUC-1460.9 , BT-S")
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
‎06-10-2021 05:21 AM in
QLED and The Frame TVs I recommend letting a service technician have a look. As we would like to gather additional information and look at this from a case by case basis please provide the full model code and the serial number of the device as well as your best contact phone number, name, and email.
Send a message on Facebook
Send Message on Twitter
Send Message to Moderator
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎06-09-2021 06:17 PM (Last edited ‎06-09-2021 06:17 PM ) in
QLED and The Frame TVs