- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-14-2021 04:42 PM (Last edited 11-26-2023 09:19 PM by SamsungChelsea ) in
Washers and DryersAfter thoroughly cleaning and reattaching the ductwork, the "ductwork clogged" symbol won't go away. Keeps coming on towards the end of the drying cycle. Any suggestions?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
01-14-2021 04:52 PM in
Washers and DryersJust to make sure, did you also clean the ductwork system in the house or building? I would also suggest resetting the circuit breaker if you haven't done that already.
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-14-2021 07:07 PM in
Washers and DryersThank you for responding. I reset the circuit breaker as you suggested and it appears to have worked. Just solely unplugging the dryer for ten minutes did not work. Thank you for your help. Much appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
01-15-2021 12:20 PM in
Washers and DryersYou're so welcome! I'm glad that it was a simple fix 🙂
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-15-2021 12:26 PM in
Washers and DryersWell I still appreciate your help, but unfortunately after one cycle of drying, the ductwork clogged symbol has come back on. Tried turning the circuit breaker back off again and cleaned off the sensor the humidity sensor in the lint basket, but no help. Any other ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
01-15-2021 12:32 PM in
Washers and DryersThe dryer is going to need service then. I'll be happy to set that up for you! Feel free to send me a private message with the serial number of the dryer. http://bit.ly/2sSxapD
Be sure to click " ✓ Accept as Solution" when you find an answer that works for you.
Please note, notification emails are a DO NOT REPLY address, you must log-in on the community page in order to respond.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-22-2021 05:16 AM in
Washers and DryersWell, we really thought it was our clogged ductwork that was causing the clogged ligth on the dryer to illuminate after ten or so minutes when the dryer was turned on. This is because we disconnected the dryer from the ductwork, turned it on and ran it for about thirty mintues. The "clogged" symbol on the machine did not turn on. So we had someone come out and clean the ductwork. The dryer is drying the clothes quickly and beautifully, but the clogged symbol is illuminating again! We've tried, while the dryer is running, switching off the circuit breaker, waiting for thirty minutes and turning the machine back on. Didn't work. Any other suggestions to reset the machine, or do I need someone to come to look at it? Can you tell me who works on Samsung dyers in my area? Bainbridge Island, Silverdale, Poulsbo, or Gig Harbor Washington would be the nearest to me.