| Custom List Message Item |
|---|
|
|
|
Freezer keeps going back to-25 after resetting it to 8 degrees Fahrenheit. Been happening continuously over the last month. View Post 
CharlieSleuther
My french door refrigerator was 5.5 years old when the freezer began to fail. We noticed first that ... View Post |
|
|
|
we recently bought a Samsung FR261BEAESR Refrigerator. The freezer is located on the bottom in the form of a drawer. When you open the drawer you... View Post 
usert59Uc6zAoX
My icemaker does the same thing, it also drops under the freezer drawer while making ice. I have loo... View Post |
|
|
|
My dishwasher is about a year and a half old. Tonight it just began to randomly turn on and off on its own. It didn't stop until I turned the... View Post 
usergLlYfYYBsh
The last post got locked after I got a response noting to look at some other troubleshooting pages..... View Post |
|
|
|
On my RF265BEAESR/AA French Door ( 3 door) refrigerator both the water light and the cube light are both on. Only the cube function works on the... View Post 
SamsungCaleb
Thank you for reaching out I understand how this may be frustrating and want to help. Try holding do... View Post |
|
My French door fridge model RF23M8070SR is stuck in demo mode. Display will flash when we try to reset but no chime. Please help View Post
SamsungCaleb
Thank you for reaching out the information in the link below should be most helpful as it will show ... View Post |
|
So my very expensive double oven just threw a C-A2 Code which has something to do with the cooling fans and/or motors. I am so off. I bought a... View Post
SamsungCaleb
I do apologize for any inconveniences this may cause, just want to confirm does this occur after pow... View Post |
|
|
|
|
|
Hi, The model of my fridge: RFG237AARS/XAA It has a 7 cube icemaker. The water dispenser is working fine. When I reset the icemaker, it takes... View Post 
BlackStallion
Glad to see you got it up an running again. Now you have a new motherboard, ice maker, an blower. No... View Post |
|
Purchased Samsung range some years ago, electric burners got really hot, not able to control.  Purchased a new range and it’s not two years old and... View Post
SamsungCaleb
I understand how this may be a cause for concern, please look at the information below to see if thi... View Post |
|
I recently bought o home that has the Family Hub refrigerator Model # RF265BEAESR - with screen. It's working fine so far, except for a small... View Post 
SamsungJam
I get how that could be a bit frustrating. I would suggest checking the wiring harness to make sure ... View Post |
|
My wife and I recently got an gas range from my in-laws. They had the board replaced in it previously and that solved the issue. (Or so we... View Post 
Tech_Blocked
@SamsungCaleb I appreciate the reply, so a few things: 1. Power cycling did not resolve the issue. A... View Post |
|
Installed this range about 3 weeks ago and everything seems to be working except the entire unit will randomly power off mid baking cycle. Â The... View Post
SamsungCaleb
I understand how this may be frustrating and want to help have you tried the troubleshooting steps b... View Post |
|
|
|
Is the fan suppose to run in Samsung Electric Range during preheating.  Can the fan be disabled View Post
BlackStallion
Its not recommended on disabling your fan. The fan runs to dispense heat throughout your oven throug... View Post |
|
|
|
|
|
Anyone else have issues with the number pad? My 0 isn't working. Followed instructions from support saying to turn the breaker off for 5... View Post
SamsungCaleb
I'm sorry to hear that, have you tried the folloing? If you have a NE63T8111** or NX60T8111** range ... View Post |
|
Hi, I am working on Samsung dishwasher DW80R5060, do anyone have by any chance wiring diagram to connect harness to this DD82-01337A control board?... View Post 
userIqbkJFbsIB
OK I have figure this out! Samsung DW80R5060US. The repairman who was called to fix it, replaced con... View Post |
|
|
|
|
|
|
|
|
|
My auto release function is not working. It is turned on but is not opening  at end cycle. Model DW80R9950 View Post
userFJd9dFZDXa
I have found a bit of lubrication seems to help. Tool in a can etc. (just a little) View Post |
|
|
